Skip to content
X-Plane 4 min read

How to fix Ortho4XP's missing Global Scenery in X-Plane 12?

Adam McEnroe
In short

Fix Ortho4XP missing Global Scenery errors in X-Plane 12 by correcting the source path, restoring DSF files and rebuilding only the overlays.

Ortho4XP's missing Global Scenery error in X-Plane 12 usually means its overlay source path is wrong, or the matching default DSF was not installed. Point custom_overlay_src at the X-Plane 12 Global Scenery package that directly contains Earth nav data, confirm the tile's DSF exists, then rebuild the overlays.

Fix the Ortho4XP source path

Correcting custom_overlay_src resolves most missing Global Scenery messages, especially after moving X-Plane or upgrading from X-Plane 11.

  1. Locate the default scenery package. Open your X-Plane 12 installation and find Global Scenery/X-Plane 12 Global Scenery.
  2. Set the overlay source. In Ortho4XP's configuration, set custom_overlay_src to that package folder. Do not select the higher Global Scenery directory or the lower Earth nav data directory.
  3. Check the source DSF. Open Earth nav data and confirm that the regional folder and DSF named in Ortho4XP's error are present.
  4. Save and rebuild the overlays. Run Ortho4XP's overlay extraction for the affected tile. A successful run normally updates the package named yOrtho4XP_Overlays.
  5. Install the output. Place or link yOrtho4XP_Overlays in X-Plane 12's Custom Scenery folder.

custom_scenery_dir is not a substitute for custom_overlay_src. The former controls where generated scenery is installed; the latter tells Ortho4XP where to read roads, buildings and other overlay data. Our complete Ortho4XP tile and overlay workflow covers the surrounding build and installation steps.

Which X-Plane 12 folder should Ortho4XP use?

Use the folder named X-Plane 12 Global Scenery that directly contains Earth nav data.

Selected folderCorrect?Reason
.../Global Scenery/X-Plane 12 Global Scenery/YesIt directly contains Earth nav data.
.../Global Scenery/NoThis is one level too high.
.../X-Plane 12 Global Scenery/Earth nav data/NoThis is one level too low; Ortho4XP adds that part of the path itself.
.../Custom Scenery/Global Airports/NoThis is an airport package, not the default overlay source.

If the error still references X-Plane 11 Global Scenery, an old drive letter or a previous installation, replace the stale path in Ortho4XP's configuration. On case-sensitive file systems, the folder names and capitalisation must also match.

What if the required DSF file is actually missing?

Repair or install the relevant X-Plane 12 scenery region if the path is correct but the DSF reported by Ortho4XP does not exist.

Errors for many land tiles usually indicate a bad source path. Failure in one geographical area more often means that region was not installed or its files are damaged. Use the X-Plane installer or your platform's scenery and file-repair controls; our Global Scenery restoration instructions explain the safe repair process.

Do not rename a neighbouring DSF or copy it over the missing file. DSF coordinates and terrain data are location-specific. A largely oceanic tile may have no useful default overlay to extract; if the orthophoto tile builds and displays correctly, that absence can be harmless.

Do I need to rebuild the whole Ortho4XP tile?

No; if only overlay extraction failed, rerun the overlay stage rather than rebuilding imagery, mesh and textures.

Check the generated zOrtho4XP tile for its own Earth nav data and texture files. If those exist and the earlier build stages completed, changing custom_overlay_src does not require a full rebuild. Rerun the terrain stages only when the generated tile DSF itself is absent or Ortho4XP stopped before creating it.

Why are buildings and roads still missing after the error is fixed?

The generated overlay must be installed without an extra nested folder and loaded above the orthophoto mesh in scenery_packs.ini.

  • Place yOrtho4XP_Overlays above all relevant zOrtho4XP tile entries.
  • Keep airport scenery above both the overlay and orthophoto mesh.
  • Remove SCENERY_PACK_DISABLED from the overlay entry if it was disabled intentionally or by an earlier test.
  • Check that the package is not nested as yOrtho4XP_Overlays/yOrtho4XP_Overlays/Earth nav data.
  • If it is linked from another drive, confirm that the link target still exists and is readable.

Default Global Scenery stays in X-Plane's Global Scenery directory; it should not be copied into Custom Scenery. For the correct airport, overlay and mesh hierarchy, use our X-Plane 12 overlay ordering guide.

AI Assistant New

Still stuck? Ask Fly Away

Ask Fly Away is our AI flight-sim assistant. Ask your exact question and get a direct, step-by-step answer in seconds — free to try.

Ask Fly Away Free preview · unlimited for PRO members