Set up and use Honeycomb Alpha and Bravo controls in X-Plane 12, with correct axis bindings, aircraft profiles, switch fixes and light setup.
To use Honeycomb controls in X-Plane 12, connect each unit before launch, open Settings > Joystick, calibrate the Alpha yoke and Bravo throttle separately, assign every axis and switch, then save an aircraft-specific control profile. Clear duplicate bindings and test full travel, detents and switch states before departure.
How do I set up Honeycomb Alpha and Bravo in X-Plane 12?
The reliable method is to configure each Honeycomb device separately rather than assuming the default assignments are correct.
- Connect the hardware before starting X-Plane. The Alpha and Bravo should appear as separate devices in the Joystick settings. If either is missing, reconnect it directly to the computer, try another USB port and restart X-Plane.
- Select each device and inspect its existing assignments. Move one control at a time and watch which on-screen axis or button responds. Clear any incorrect or duplicated binding before adding another.
- Calibrate all analogue axes. Move the Alpha through its full pitch and roll travel, then move every Bravo lever through its complete range. Calibrate rudder and toe-brake axes separately if pedals are connected; the Alpha and Bravo do not provide a rudder axis.
- Assign the flight axes. Set the Alpha to pitch and roll. Assign the Bravo levers according to the aircraft rather than their physical colour alone.
- Check axis direction. If the cockpit control moves backwards, enable the axis reversal option. Do not use that option to create reverse thrust; it reverses the entire axis.
- Map buttons and switches. Use explicit up, down, on and off commands where available. Maintained switches can become out of step with the cockpit if they are bound to a generic toggle command.
- Create an aircraft profile. Save separate profiles for piston singles, twins, turboprops and jets. Associate the appropriate profile with each aircraft so X-Plane loads it automatically.
- Test before flight. Check the control surfaces, throttles, propellers, mixtures, brakes, gear, flaps and reverse controls from an external view or cockpit indication.
For the underlying calibration, duplicate-binding and profile workflow, see our complete X-Plane input-device setup procedure. Bravo owners can use our detailed Bravo axis and switch configuration for device-specific instructions.
Which axes should I assign to the Honeycomb controls?
Axis assignments should match the engine and control layout of the aircraft being flown.
| Physical control | Typical X-Plane assignment | Application |
|---|---|---|
| Alpha fore and aft | Pitch | All aircraft |
| Alpha left and right | Roll | All aircraft |
| Bravo black lever | Throttle or engine-specific throttle | Piston, turboprop or jet |
| Bravo blue lever | Propeller or engine-specific propeller | Constant-speed piston and turboprop aircraft |
| Bravo red lever | Mixture or engine-specific mixture | Piston aircraft |
| Available Bravo lever | Speedbrake, flap or condition control | Only where the aircraft supports that axis |
| Pedal centre axis | Yaw | Separate rudder pedals |
| Pedal toe axes | Left and right toe brake | Separate rudder pedals |
The removable lever colours are only visual labels; they do not change what an axis sends to X-Plane. For a twin, assign separate throttle, propeller and mixture or condition axes to each engine. Our engine-by-engine throttle assignment guide explains when to use generic controls and when to use numbered engine axes.
How should Honeycomb switches and detents be assigned?
Assign maintained switches to explicit on/off commands, while momentary buttons normally suit toggle, hold or step commands.
- Gear lever: bind its two positions to gear up and gear down rather than assigning both to a single gear-toggle command.
- Flap switch: use flap up a notch and flap down a notch unless the aircraft provides a supported flap axis.
- Alpha electrical switches: choose separate on and off commands when they are available. A toggle command can leave the hardware and virtual cockpit showing opposite states.
- Ignition selector: map each position to the corresponding magneto or starter command. Complex aircraft may expose their own commands instead of responding to X-Plane's standard ones.
- Reverse detents: assign the detent buttons or supported reverse range to the aircraft's reverse-thrust command. The axis reversal checkbox is not a substitute for reverse thrust.
- Autopilot buttons: verify every mode in the cockpit. Aircraft with custom avionics may require aircraft-specific commands and a dedicated profile.
Do Honeycomb controls need separate software?
Basic axes and most buttons normally work as standard USB inputs, but Bravo annunciator lights and some aircraft-specific functions may require Honeycomb integration software, a plugin or a suitable profile.
The LEDs are output indicators, so dark annunciators do not necessarily mean the Bravo's axes and buttons have failed. Installation and profile requirements can differ by operating system and aircraft; our Bravo drivers, profiles and annunciator-light guide separates native X-Plane assignments from the additional integration layer.
Why are my Honeycomb controls not working correctly?
Most Honeycomb problems in X-Plane 12 come from duplicate assignments, the wrong active profile or commands that do not match the physical switch type.
- One movement controls two functions: inspect every connected device for duplicate pitch, roll, yaw or throttle assignments. X-Plane can retain an unwanted default binding on another controller.
- All engines move together: replace the generic throttle assignment with numbered engine axes where independent control is required.
- An axis moves backwards: reverse that individual axis, then recalibrate and check its full travel.
- A switch works once and then appears reversed: replace its toggle command with separate on and off commands.
- The setup works in one aircraft only: check which control profile is active. Custom aircraft may use different commands from X-Plane's standard aircraft.
- Levers jitter near idle or a detent: recalibrate first. If the hardware is otherwise stable, add only a small dead zone or response-curve adjustment rather than masking a large section of travel.
- The yoke works but there is no steering or rudder: connect and assign rudder pedals, or use another yaw input. Turning the Alpha yoke controls roll, not yaw.
- The Bravo lights remain dark: confirm the integration software or plugin is loaded and that the selected light profile supports the aircraft. Axis operation and annunciator operation are separate systems.