Skip to content
General 5 min read

How do I download and install Little Navmap on Mac?

Adam McEnroe
In short

Download and install Little Navmap on Mac correctly, with Apple Silicon selection, Gatekeeper fixes, X-Plane scenery and live connection setup.

Download the macOS build of Little Navmap, choosing the package that matches your Mac's processor when separate Apple Silicon and Intel builds are offered. Extract it fully, move Little Navmap to Applications, open it through Gatekeeper if prompted, then load your simulator scenery and install its live-connection component if required.

Little Navmap is a general flight-planning utility rather than a simulator. On a Mac it is most commonly paired with X-Plane, although it can also connect over a network to a supported simulator running on a Windows PC.

Which Little Navmap Mac download should I choose?

Choose a native Apple Silicon build for an M-series Mac, an Intel build for an Intel Mac, or a Universal build for either processor.

Build labelChoose it whenWhat to know
Apple Silicon or arm64About This Mac identifies an Apple M-series chipThis is the preferred native build for Apple Silicon.
Intel or x86_64About This Mac lists an Intel processorAn Apple Silicon Mac may run it through Rosetta when no native build is available.
UniversalYou have either processor typeThis package contains support for both architectures where offered.

Our Little Navmap package and platform information provides a suitable starting point. Check that the listed file supports macOS and matches your processor before downloading; a Windows installer will not run on a Mac.

How do I install Little Navmap on macOS?

Little Navmap is normally installed by extracting or opening its downloaded package and placing the application in the Applications folder.

  1. Quit older copies. Close Little Navmap before replacing or moving an existing installation.
  2. Extract the download completely. Double-click a ZIP archive in Finder, or open the disk image if the release uses one. Do not launch the application from a ZIP preview or other temporary location. Our guide to extracting simulator downloads correctly covers incomplete and double-nested archives.
  3. Move the application. Drag Little Navmap.app, shown in Finder as Little Navmap, into Applications. Keep any supplied helper or plug-in folders until simulator setup is complete.
  4. Open it for the first time. Double-click the application. If macOS blocks it, use the Gatekeeper procedure below rather than disabling system security.
  5. Load the simulator scenery. In Little Navmap, use the Load Scenery Library command, select the appropriate simulator type and point it at the simulator's main folder. For X-Plane, choose the folder containing the X-Plane application and Resources, not just Custom Scenery.

How do I open Little Navmap if Gatekeeper blocks it?

Control-click Little Navmap in Applications, choose Open, and confirm the second Open command if you trust the downloaded package.

If that option does not appear, try opening the application once, then look under Privacy and Security in System Settings for Open Anyway. Older macOS releases place the equivalent control under Security and Privacy in System Preferences.

An "app is damaged" message can also mean the archive was incomplete, the wrong processor build was downloaded or macOS quarantined part of the extracted package. Delete that copy, download it again and extract it before moving it to Applications. Do not disable Gatekeeper globally; use our Little Navmap access and permissions fixes if the warning remains.

How do I connect Little Navmap to X-Plane on Mac?

Load the X-Plane scenery library in Little Navmap, then install the matching Little Xpconnect plug-in to receive the live aircraft position.

  1. Find Little Xpconnect. Use the companion plug-in supplied for the same Little Navmap release.
  2. Copy the whole plug-in folder. Place Little Xpconnect inside the X-Plane Resources/plugins directory. For X-Plane 12, the resulting path should resemble X-Plane 12/Resources/plugins/Little Xpconnect.
  3. Check the folder nesting. A common mistake is creating two successive Little Xpconnect folders. X-Plane must be able to find the plug-in files directly inside the first plug-in folder.
  4. Restart X-Plane. Start or restart the simulator, open Little Navmap and use its flight-simulator connection command. A same-Mac installation uses a local connection.

Do not place the Little Navmap application itself in X-Plane's plug-ins folder. Little Navmap can create routes without Little Xpconnect; the plug-in is needed for live simulator tracking.

Connecting to a Windows simulator over the network

A Mac running Little Navmap can connect to a supported Windows simulator by running the matching Little Navconnect helper on the simulator PC. Both computers should be on the same local network, and the Windows firewall must permit the helper on private networks.

Enter the Windows computer's local address and the port shown by Little Navconnect in Little Navmap's connection dialogue. This is the practical arrangement for MSFS, FSX or Prepar3D because those simulators do not run natively on macOS.

Common Mac installation problems

Most Little Navmap installation failures come from the wrong processor build, incomplete extraction, macOS permissions or an incorrectly installed X-Plane plug-in.

  • The application closes immediately: confirm that its architecture and minimum macOS requirement match the Mac.
  • No X-Plane scenery appears: select the X-Plane root folder and reload the scenery library. Scan it again after installing or removing scenery.
  • The aircraft does not appear on the map: verify the Little Xpconnect folder location and examine Log.txt in the X-Plane folder for plug-in loading errors.
  • X-Plane is on an external drive: approve any Files and Folders or removable-volume access request for Little Navmap. Denying it can leave the scenery database empty.
  • An update installs but tracking stops: replace the older Little Xpconnect component with the version supplied alongside the updated application.

Application updates normally leave settings, user points and aircraft performance data in the Mac user profile, but exporting valuable custom data before a major replacement is sensible. Once the installation works, our Little Navmap planning and simulator-connection walkthrough explains route creation, map use and flight-plan export.

AI Assistant New

Still stuck? Ask Fly Away

Ask Fly Away is our AI flight-sim assistant. Ask your exact question and get a direct, step-by-step answer in seconds — free to try.

Ask Fly Away Free preview · unlimited for PRO members