Set up X-Plane 11 multiplayer online by direct IP or a public flying network, with port, firewall, traffic model and connection fixes.
To play X-Plane 11 multiplayer online, either connect each copy directly by IP in Settings > Network, allowing the selected UDP port through the router and firewall, or use a compatible pilot client for an organised network such as VATSIM. X-Plane 11 has no built-in public server browser or matchmaking.
Which multiplayer method should I use?
Use direct IP for a private flight with people you know; use an organised network when you want public traffic and human air traffic control.
| Method | Best for | Main limitation |
|---|---|---|
| Built-in direct IP | Private formation flights and small groups | Requires IP and port configuration; no public lobby or shared cockpit |
| Online pilot network | Public traffic, flight plans and human ATC | Requires an account, compatible pilot client and traffic models |
| Shared-cockpit add-on | Two people operating one aircraft | Must explicitly support X-Plane 11 and the chosen aircraft |
Our comparison of direct-IP, lobby and network-based multiplayer explains why X-Plane does not behave like a simulator with a conventional list of public servers.
How do I set up direct-IP multiplayer in X-Plane 11?
X-Plane 11's built-in multiplayer works by sending aircraft data directly between copies of the simulator.
- Match the software. All pilots should use X-Plane 11 at the same update level where practical. Temporarily disable other traffic or networking plugins while testing.
- Check the receive port. Open
Settings > Networkand locate the multiplayer section. X-Plane commonly uses UDP port49000, but use the receive port displayed in your installation if it differs. - Allow incoming UDP traffic. Permit X-Plane through the operating system firewall. For an internet connection, forward the selected UDP port from each router to the local IP address of the appropriate simulator computer. Forwarding TCP alone will not work.
- Add every remote pilot. In the multiplayer section, choose
Add External Machineand enter the other pilot's IP address and receive port. Use the computer's private IPv4 address for a local network, or the router's public IPv4 address for an internet connection. Repeat this on every copy of X-Plane. - Test with two aircraft first. Load at the same airport but use different parking positions. Once both aircraft appear and move correctly, add any remaining pilots.
With more than two pilots, each copy normally needs an entry for every other participant. If several X-Plane computers sit behind one router, assign separate receive ports where the network settings permit it and forward each port to the correct local computer.
Do not place the simulator computer in the router's DMZ merely to avoid configuring a port. If the internet provider uses carrier-grade NAT, or there are two routers performing NAT, ordinary port forwarding may not provide a reachable public address. An organised pilot network is usually easier in that situation because its client makes an outbound connection.
How do I join public X-Plane 11 multiplayer?
Public X-Plane 11 flying requires a compatible pilot client for a network such as VATSIM rather than the built-in direct-IP feature.
- Check X-Plane 11 compatibility. Do not assume the newest release of a pilot client still supports X-Plane 11; verify that the client explicitly lists it.
- Install traffic models. CSL models let the client represent other pilots as the correct aircraft type and livery instead of a generic or missing model. Our instructions for installing Bluebell CSL aircraft models cover the usual folder and model-path problems.
- Connect while parked. Load at a stand or gate, enter the correct callsign and departure airport in the pilot client, then connect. Never appear on an occupied runway.
- Configure traffic and audio. Follow the client's instructions for traffic injection, TCAS and voice. These settings vary between clients, so old advice about AI aircraft slots may be wrong for the client being used.
If the connection succeeds but traffic or controllers are absent, use our X-Plane checks for displaying online traffic and human ATC.
Why can I not see the other aircraft?
If no traffic appears, the usual cause is one-way peer configuration, a wrong IP address, blocked UDP traffic or missing model matching.
- Only one pilot sees the other: check the firewall and port forwarding at the computer that cannot receive aircraft data. Direct-IP entries must normally exist at both ends.
- Both computers are in the same house: use their local addresses, such as
192.168.x.x. The public address may fail if the router does not support NAT loopback. - The public address never responds: check for double NAT or carrier-grade NAT. The address reported by the router may not be directly reachable from the internet.
- The aircraft type or livery is wrong: the connection is working, but the required local aircraft or CSL model is missing or incorrectly mapped.
- Traffic appears visually but not on TCAS: review the pilot client's traffic-injection settings rather than changing the router.
- X-Plane stutters or closes after connecting: remove conflicting traffic plugins and work through our X-Plane online freeze and crash checklist.
Does X-Plane 11 multiplayer share the cockpit?
No. Built-in X-Plane 11 multiplayer represents separate aircraft and does not synchronise cockpit switches, the flight management system or aircraft systems between two pilots.
Shared cockpit flying requires a separate tool that supports X-Plane 11 and the exact aircraft add-on. Both pilots should use matching aircraft versions because even small differences in systems or datarefs can cause controls, displays and autopilot modes to disagree.
Can X-Plane 11 and X-Plane 12 fly together?
Not reliably through built-in direct-IP multiplayer, so private peer sessions should use the same X-Plane major version and preferably the same update level.
Pilots using X-Plane 11 and X-Plane 12 can share an organised online network when each simulator has a supported pilot client. The network exchanges standardised traffic data, while each computer renders the other aircraft through its own local models.