Learn how to use autopilot in X-Plane 12: set heading, NAV, altitude, VS or FLC, read mode annunciations, fly approaches and fix common errors.
To use autopilot in X-Plane 12, stabilise and trim the aircraft, select a heading or navigation source, set the target altitude, engage the flight director and autopilot, then choose lateral and vertical modes. Confirm the mode annunciations: the autopilot follows active modes, not merely the values shown on the panel.
Autopilot controls and modes in X-Plane 12
The available controls depend on the autopilot fitted to the selected aircraft. A Cessna, an airliner and a third-party aircraft may use different labels and engagement logic, although the underlying modes are similar.
| Control or mode | What it does | Common mistake |
|---|---|---|
| FD | Displays flight-director commands. | The command bars do not control the aircraft unless AP is engaged. |
| AP | Engages the autopilot servos. | AP engagement alone may only hold the present pitch and bank. |
| HDG | Turns towards and follows the heading bug. | Changing the bug has no effect unless HDG mode is active. |
| NAV or LNAV | Tracks the selected GPS, FMS or radio-navigation course. | The wrong navigation source is selected, or the route leg is not active. |
| ALT | Holds an altitude, normally the altitude at which the mode activates. | Setting a new altitude does not by itself command a climb or descent. |
| VS | Maintains a selected vertical speed. | An excessive climb rate causes airspeed to decay. |
| FLC or IAS | Pitches to maintain a selected airspeed during a climb or descent. | The pilot fails to add or reduce power. |
| APR | Arms approach-course and vertical-guidance capture. | The aircraft approaches from the wrong side, above the glide path or with the wrong source selected. |
| YD | Uses the yaw damper to reduce unwanted yaw. | YD does not steer the aircraft or replace an autopilot mode. |
How do I engage the autopilot?
The safest generic sequence is to configure the targets first, engage the system in stable flight and then verify exactly what became active.
- Hand-fly and trim the aircraft. Establish a sensible pitch, bank, airspeed and power setting before engagement. Do not ask the autopilot to recover a badly out-of-trim aircraft.
- Set the lateral target. Move the heading bug for HDG mode, or activate the required GPS, FMS, VOR or localiser course for NAV mode.
- Set the altitude. Enter the desired altitude in the preselector if the installed system has one.
- Choose a vertical mode. Use ALT to remain level, VS for a selected rate, or FLC or IAS to climb or descend at a selected airspeed.
- Engage FD and AP. Some systems allow modes to be selected before AP engagement; others initially enter basic roll and pitch modes. Follow the fitted aircraft's panel logic.
- Read the flight-mode annunciator. Confirm one active lateral mode and one active vertical mode. Armed modes are waiting for capture and are not yet controlling the aircraft.
- Monitor power, speed and trim. Unless the aircraft has an engaged autothrottle, the pilot remains responsible for throttle movement and airspeed management.
For the default-style Garmin installation, our G1000 mode and control walkthrough explains the panel buttons and active-versus-armed indications in more detail.
Should I use HDG or NAV mode?
Use HDG when you want the aircraft to follow the heading bug; use NAV or LNAV when it should track an active radio course or flight-plan leg.
- HDG: Best for departure turns, radar vectors, avoiding weather and positioning for an approach. Set the bug first, then engage HDG.
- NAV or LNAV: Best for following an activated GPS or FMS route. The current leg must be valid, and the aircraft must be positioned so the autopilot can intercept it.
- APR: Use for a supported instrument approach after the correct approach and navigation source have been selected.
If no route is available for NAV mode to follow, use our instructions for building and activating an X-Plane 12 flight plan. In aircraft fitted with older Garmin equipment, our Garmin GNS 430/530 source-selection guide covers the easily missed GPS/VLOC switch.
How do I make the autopilot climb or descend?
Selecting a different altitude normally sets a capture target; it does not start the climb or descent. You must also engage an appropriate vertical mode.
Using vertical speed mode
Set the target altitude, press VS and select a modest climb or descent rate. The autopilot maintains that rate while you use power to protect the airspeed. Reduce the selected climb rate if the aircraft becomes slow.
Using FLC or IAS mode
Set the target altitude, engage FLC or IAS and select the required airspeed. The autopilot changes pitch to hold that speed, while you set climb power or reduce power for descent. FLC does not usually move the throttles in a general-aviation aircraft.
Capturing the selected altitude
Watch for an altitude-capture indication to arm and then become active. Advanced systems capture the preselected altitude automatically; a basic autopilot may require you to press ALT manually as the aircraft reaches the desired level.
Can X-Plane 12 autopilot fly an approach and land?
An autopilot can track a compatible ILS or GPS approach, but it can land automatically only when the simulated aircraft and its fitted system specifically support autoland.
- Load and activate the approach. Check the final course, minimum altitude and navigation source.
- Intercept correctly. Approach the final course at a manageable angle. For an ILS, intercept the glideslope from below unless the aircraft documentation specifies different logic.
- Arm APR mode. Confirm that localiser and glideslope modes, or their GPS equivalents, are armed.
- Verify capture. Do not descend merely because APR was pressed; wait until the lateral and vertical modes show as active.
- Manage the rest of the aircraft. Gear, flaps, power and landing checks remain the pilot's responsibility unless the aircraft explicitly automates them.
Most general-aviation autopilots should be disconnected before landing. Airliner autoland also requires the correct approach capability, aircraft configuration and engagement of every system specified by that aircraft's procedure.
Why is the autopilot not following my settings?
The most common cause is that the desired mode is armed rather than active, although an incorrect navigation source is nearly as frequent.
- Nothing happens after changing altitude: Select VS, FLC or another climb or descent mode; the altitude knob alone is only a target.
- NAV will not capture: Check GPS versus VLOC, activate the intended leg and intercept it at a shallower angle.
- APR will not descend: Confirm valid vertical guidance and approach from below the glide path. Some GPS approaches provide lateral guidance only.
- FLC goes the wrong way: Check the selected altitude and apply suitable power. FLC controls pitch for airspeed, not thrust.
- The aircraft slows in VS: Add power or reduce the commanded climb rate.
- AP will not engage: Centre the controls, trim the aircraft and check electrical power, failures and any aircraft-specific engagement conditions.
- AP drops out: Avoid fighting the servos with the controls and check for excessive pitch, bank, trim forces or system failures. Our guide to diagnosing unexpected X-Plane 12 autopilot disconnects covers this fault separately.
Third-party aircraft may use custom autopilot code and custom control commands. If a keyboard or yoke assignment works in one aircraft but not another, bind the aircraft's intended autopilot-disconnect or servo command rather than assuming every model uses the same generic X-Plane command.
How should I disconnect the autopilot?
Disconnect with the assigned yoke, joystick or panel control while holding the aircraft's present attitude, then retrim for manual flight.
- Place a hand on the controls. Match the control pressure before disengaging.
- Press the disconnect control. Confirm the aural or visual warning and check that AP is no longer annunciated.
- Retrim promptly. A pitch change after disconnection usually means the aircraft was not trimmed for its present speed and configuration.
- Check separate automation. The flight director, autothrottle or yaw damper may remain active after AP disconnect and may need separate action.