FSX / P3D scenery

FSX Flying W Airport Scenery

Flying W Airport (N14) brings Lumberton, New Jersey to life with satellite-referenced placement, realistic GA and helicopter parking options, and seasonal summer trees, plus 100LL and Jet-A fueling at the terminal ramps. Designed for FSX and requires MegaScenery Earth New Jersey/Delaware 002 for best alignment and apron blending.

165 downloads 805.26 KB Scanned clean

United States of America

Flight Simulator X Prepar3D

Scenery Flying W Airport (N14), NJ. Located one mile SW of Lumberton, New Jersey on 170 acres of land, Flying W Airport services small to medium GA aircraft as well as helicopters. Transient storage are tie downs only. There are plenty of places to park. The main parking area in on the west side of the airport on the south end of the north tarmac and can handle wingspans of up to 50 feet. You can also park slightly north among the static aircraft or east of the runway on the grass. Collisions are disabled with static craft in these areas to assist with parking. Both 100LL and Jet-A are available by stopping at the south tarmac next to the fuel tank or the north tarmac by the fuel trucks in front of the terminal. Trees are summertime only. By Drew Sikora.

Scenery constructed with use of satellite images/streetview, the author has not been there in person.

This scenery is meant to be used in conjunction with MegaScenery Earth New Jersey/Delaware 002. It is not required, but apron use is minimized to allow satellite scenery to show through as much as possible, and objects are placed based on the MSE textures - lack of it may make scenery look out of place.

Airport Remarks:

- Fuel Available: 100LL (blue), Jet-A.
- Wind Indicator: Yes, Lighted.
- Runway 1 caution: 89 ft Trees 262 ft from runway, 169 ft right of center.

Installation:

Unzip the folder N14 to wherever you stash your add-on scenery, then activate within the FSX scenery library.

This airport uses the following external scenery objects:
EZ Scenery Objects
RWY 12 Objects
hclib1.zip
Helicopters_A_library.zip
jrbcntnr.zip
fs9_custombuildings_ss_1_v2.zip
GA Hangars SS V3

NOTE: the airport AD2 file in the main airport directory is the Airport Design Editor file for anyone that wants to further tweak the airport.

Disclaimer:

There is no reason installation of this scenery should harm your computer. I will not be held responsible for any damage occured to your computer as result of installing this scenery. Use at your own risk.

Ready to download Flying W Airport Scenery?

Free for all simmers · 805.26 KB · Scanned clean

File information

Filename

n14.zip

File size

805.26 KB

Virus scan

Clean (scanned with ClamAV)

Access

Freeware

Content rating

Everyone

Download speed: Free tier is capped at 0.5 Mbps. PRO members download at full line speed.

This is a freeware file — use is subject to our freeware copyright terms.

How to install this mod

FSX / P3D scenery

Extract the downloaded archive

Use 7-Zip (free) or WinRAR to extract the ZIP to a temporary folder. Don't install while still zipped — the simulator can't read inside ZIP files.
Place scenery in Addon Scenery

Create a folder under FSX\Addon Scenery\ containing scenery and texture sub-folders.
Activate in Scenery Library

In FSX, go to Settings → Scenery Library → Add Area. Higher priority means it overrides lower entries for the same location.
Always read the included readme

Every mod ships with a readme.txt or README file. It tells you exactly where files go, what dependencies are needed, and any quirks specific to this add-on.

Finding the scenery

Use these coordinates to fly directly to this location once the mod is installed.

FSX / Prepar3D coordinates (or generate a flight plan)

39.93560000,-74.80720000

Decimal degrees

39.935600°, -74.807200°

Degrees, minutes, seconds

39° 56' 08.160" N 74° 48' 25.920" W

Launch FSX or Prepar3D and use Flights → Load to open the downloaded .pln file. Your aircraft will be positioned at this location.

What’s inside this archive

The archive n14.zip has 8 files and directories contained within it.

File Contents

This list displays the first 500 files in the package. If the package has more, you will need to download it to view them.

Filename/Directory	File Date	File Size
N14	10.24.10	0 B
N14_ADEX_DS.ad2	10.24.10	814.57 kB
Scenery	10.24.10	0 B
N14_ADEX_DS.BGL	10.24.10	57.96 kB
N14_ADEX_DS_CVX.bgl	10.24.10	661 B
ReadMe.txt	10.24.10	3.25 kB
flyawaysimulation.txt	10.29.13	959 B
Go to Fly Away Simulation.url	01.22.16	52 B