FSX / P3D scenery

FSX Pemberton Airport Scenery

Pemberton Airport 3N7 scenery recreates the private New Jersey airstrip with satellite-placed buildings, seasonal summer trees, and tie-down parking at the runway 22 end, tuned to keep apron coverage minimal for photo ground textures. Built for FSX, it requires MegaScenery Earth New Jersey/Delaware 002 plus listed object libraries for full detail.

5/5 (1) 118 downloads 1.12 MB Scanned clean

United States of America

Flight Simulator X Prepar3D

Pemberton Airport (3N7), New Jersey (NJ). Located one mile northwest of Pemberton, New Jersey on 14 acres of land, Pemberton Airport is a private airstrip. Tie down areas are available at the runway 22 end. The single parking space is a tie down - do not use if your aircraft's wingspan is greater than 50 feet. Note that the actual listing for this airport in real world databases is 3NJ1. Trees are summertime only. By Drew Sikora.

Scenery constructed with use of satellite images/streetview, the author has not been there in person.

This scenery is meant to be used in conjunction with MegaScenery Earth New Jersey/Delaware 002. It is not required, but apron use is minimized to allow satellite scenery to show through as much as possible, and objects are placed based on the MSE textures - lack of it may make scenery look out of place.

Airport Remarks:

- No Fuel Available
- Wind Indicator: Yes, Not Lighted
- Airport is unlit - VFR use only

Installation:

Unzip the folder 3N7 (3NJ1) to wherever you stash your add-on scenery, then activate within the FSX scenery library.

When layering in your scenery library, this airport file MUST be layered ON TOP of MegaScenery Earth layers. If you do not do this, you will get floating runways in areas with hills and mountains depending on how detailed your terrain mesh is.

This airport uses the following external scenery objects:
EZ Scenery Objects
RWY 12 Objects
OZx Libraries 1.0
ezhousz.zip
GA Hangars SS V3
ezvinhg3.zip
fs9_custom_objects_ss_1_v2.zip
ga_hangers.zip

The scenery libraries above ARE REQUIRED to get the full effect of the scenery.

NOTE: the airport AD2 file in the main airport directory is the Airport Design Editor file for anyone that wants to further tweak the airport.

There is no reason installation of this scenery should harm your computer. I will not be held responsible for any damage occured to your computer as result of installing this scenery. Use at your own risk.

Ready to download Pemberton Airport Scenery?

Free for all simmers · 1.12 MB · Scanned clean

File information

Filename

3n7.zip

File size

1.12 MB

Virus scan

Clean (scanned with ClamAV)

Access

Freeware

Content rating

Everyone

Download speed: Free tier is capped at 0.5 Mbps. PRO members download at full line speed.

This is a freeware file — use is subject to our freeware copyright terms.

How to install this mod

FSX / P3D scenery

Extract the downloaded archive

Use 7-Zip (free) or WinRAR to extract the ZIP to a temporary folder. Don't install while still zipped — the simulator can't read inside ZIP files.
Place scenery in Addon Scenery

Create a folder under FSX\Addon Scenery\ containing scenery and texture sub-folders.
Activate in Scenery Library

In FSX, go to Settings → Scenery Library → Add Area. Higher priority means it overrides lower entries for the same location.
Always read the included readme

Every mod ships with a readme.txt or README file. It tells you exactly where files go, what dependencies are needed, and any quirks specific to this add-on.

Finding the scenery

Use these coordinates to fly directly to this location once the mod is installed.

FSX / Prepar3D coordinates (or generate a flight plan)

39.97000000,-74.68000000

Decimal degrees

39.970000°, -74.680000°

Degrees, minutes, seconds

39° 58' 12.000" N 74° 40' 48.000" W

Launch FSX or Prepar3D and use Flights → Load to open the downloaded .pln file. Your aircraft will be positioned at this location.

What’s inside this archive

The archive 3n7.zip has 8 files and directories contained within it.

File Contents

This list displays the first 500 files in the package. If the package has more, you will need to download it to view them.

Filename/Directory	File Date	File Size
3N7 (3NJ1)	11.22.10	0 B
3N7_ADEX_DS.ad2	11.22.10	1.16 MB
Scenery	11.22.10	0 B
3N7_ADEX_DS.BGL	11.22.10	109.40 kB
3N7_ADEX_DS_CVX.bgl	11.22.10	1.04 kB
ReadMe.txt	11.22.10	3.06 kB
flyawaysimulation.txt	10.29.13	959 B
Go to Fly Away Simulation.url	01.22.16	52 B