Skip to content
Microsoft Flight Simulator 5 min read

How do I set a custom FOV in MSFS 2024?

Ian Stephens
In short

Set a custom FOV in MSFS 2024 using cockpit zoom, pilot eyepoint controls and saved camera slots, plus fixes for resets and axis conflicts.

MSFS 2024 has no universal numeric field for entering an exact field-of-view angle. In the cockpit, set a custom FOV with camera zoom, position the pilot eyepoint separately, then save both in a custom camera slot. External-camera zoom is separate and must be adjusted in that camera mode.

How do I set and save a custom cockpit FOV?

Use cockpit zoom for the viewing angle and camera translation for the pilot's seating position.

  1. Enter the cockpit camera. Reset the view first so that an old offset or head-tracking position does not affect your setup.
  2. Position the pilot eyepoint. Move the camera up, down, forwards or backwards until the glareshield, horizon and primary instruments sit naturally. Our guide to setting the pilot eyepoint without distorting perspective covers these translation controls.
  3. Adjust cockpit zoom. Zooming out produces a wider FOV and shows more of the cockpit; zooming in narrows the FOV and makes instruments larger. Search the control settings for zoom if your current keyboard, controller or joystick profile has no suitable binding. You can also map cockpit zoom and tune its response speed.
  4. Check the view in normal flying conditions. Look straight ahead and confirm that the runway remains visible over the panel, important instruments are readable, and the edges are not excessively stretched.
  5. Save the finished view. Bind or use a Save Custom Camera slot, then assign the corresponding Load Custom Camera command. The procedure for storing and recalling an aircraft-specific camera preset explains the slot system in detail.

Zoom Speed only controls how quickly the zoom changes while you press or move the input. It does not alter the saved FOV, image quality or available zoom range.

Can I enter an exact FOV in degrees?

No, the standard MSFS 2024 camera interface does not offer a dependable box for entering a horizontal or vertical FOV in degrees.

The apparent view also depends on monitor aspect ratio, screen size, viewing distance and aircraft cockpit geometry. A zoom setting that looks balanced on a 16:9 display may feel too narrow on an ultrawide monitor, while the same setting can frame two aircraft very differently.

Manual camera-file editing on PC is a poor first choice because camera definitions can be replaced by aircraft or simulator updates, and their zoom values should not be treated as guaranteed FOV measurements in degrees. A saved custom view is safer and easier to correct.

Should I change zoom or move the pilot seat?

Use zoom to change how wide the scene appears, and move the camera when the pilot's head is simply in the wrong place.

ControlUse it whenWhat it changes
Cockpit zoomToo much or too little of the cockpit is visibleThe field of view; it does not physically move the pilot
Camera translationThe view is too high, low, close or far from the panelThe pilot eyepoint without changing the lens angle
Look or panYou need to inspect another part of the cockpit temporarilyThe viewing direction, not the base FOV

A mistake we see constantly is using an extremely wide zoom to compensate for a seat position that is too close to the panel. Move the eyepoint backwards first, then widen the FOV only as much as necessary.

Why does my custom FOV change or reset?

A custom FOV normally appears to reset because the wrong camera mode or custom slot is active, or because another input is still controlling zoom.

  • The outside view changes instead: cockpit and external cameras have separate zoom contexts. Return to the cockpit before adjusting or saving the view.
  • The FOV slowly moves: check for duplicate zoom assignments and noisy joystick, throttle or controller axes. Remove the extra binding or add a small dead zone.
  • The view shifts with head tracking: centre or temporarily disable tracking while building the base view. Re-enable it after saving the slot.
  • The simulator opens on its default camera: load your custom slot after entering the aircraft. Saving a view does not necessarily make it the automatic opening view.
  • One aircraft ignores the view: custom cockpit framing is aircraft-specific. Save a separate view for each aircraft or significantly different cockpit variant.
  • An aircraft update changes the framing: its camera reference position may have changed. Reset the camera, rebuild the eyepoint and save the slot again.

If bindings are acting in an unexpected camera mode, use our reference to the separate cockpit, external, zoom and translation controls to identify the conflicting command.

What FOV works best in MSFS 2024?

Choose the narrowest FOV that still gives you the cockpit visibility needed for normal flying.

A very wide setting exposes more instruments but makes them smaller and can stretch scenery near the screen edges. A narrow setting gives a more natural forward perspective and clearer instruments, but requires more panning or head movement. On an ultrawide display, start moderately wide rather than at the maximum and judge the result by edge distortion, instrument readability and runway visibility.

AI Assistant New

Still stuck? Ask Fly Away

Ask Fly Away is our AI flight-sim assistant. Ask your exact question and get a direct, step-by-step answer in seconds — free to try.

Ask Fly Away Free preview · unlimited for PRO members